shopping_cart Cart (0)
Victron Phoenix Smart IP43 12V / 50A (1+1) Battery Charger
€417.19
Tax included
12
V
V
Measurements: 180 x 249 x 100 mm
EAN/GTIN: 8719076041627
Victron Phoenix Smart IP43 12V / 50A (1+1) Battery Charger
The Victron Phoenix Smart IP43 12/50 (1+1) Battery Charger is a high-quality battery charger that is designed to be versatile and reliable. It is part of the Phoenix Smart IP43 range of chargers from Victron Energy, which is a leading manufacturer of power conversion and battery charging solutions.
The Victron Phoenix Smart IP43 is a professional battery charger with integrated Bluetooth that can be used in devices in your workshop as well as in motor vehicles, such as vintage cars, motorcycles, boats, tractors, RVs and campervans.
The Victron Phoenix Smart IP43 12/50 (1+1) Battery Charger has a 6-stage adaptative fully automatic charging algorithim and it features 2 outputs to charge 2 battery banks, with a voltage of 12V, and a charging current of 50A.
Please note that the AC-connection included in the product is a IEC 320 C14 inlet with retainer clip. AC cord with country specific plug must be ordered separately. See below for the correct specific reference, under Victron Accesories for the Phoenix Smart IP43 12/50 (1+1) (not inlcuded in the product).
Specifications
| Victron Phoenix Smart IP43 12/50 (1+1) Charger | PSC125051085 |
| Input voltage range | 230 VAC (range: 210 – 250 V) |
| DC input voltage range | 290 – 355 VDC |
| Charge current, normal mode | 50A |
| Charge current, NIGHT or LOW | 25A |
| Efficiency | 92 % |
| No load power consumption | 1 W |
| Frequency | 45 – 65 Hz |
| Number of outputs | (1+1) models: 2 (2nd output via 2 pole terminal & 3 A max) |
| Charge voltage 'absorption' | Normal: 14,4 V High: 14,7 V Li-ion: 14,2 V |
| Charge voltage 'float' | Normal: 13,8 V High: 13,8 V Li-ion: 13,5 V |
| Charge voltage 'storage' | Normal: 13,2 V High: 13,2 V Li-ion: 13,5 V |
| Charge algorithm | 6-stage adaptive: test - bulk – absorption - recondition – float – storage e (3-stage for Li-ion) |
| Can be used as power supply | Yes, output voltage can be set with Bluetooth and/or VE.Direct |
| Protection | Battery reverse polarity (fuse) Output short circuit Over temperature |
| Operating temp. range | -40 to +60 °C (Rated output current up to 40 °C, derate linearly to 20 % at 60 °C) |
| Humidity (non-condensing) | Max 95 % |
| Remote on/off | Yes (2-pole terminal) |
| Relay (programmable) | DC rating: 5 A up to 28 VDC |
| Bluetooth | Power: -4 dBm | Frequency: 2402 – 2480 MHz |
| Battery connection | Screw terminals 16 mm² / AWG6 |
| 230 VAC connection | IEC 320 C14 inlet with retainer clip (AC cord with country specific plug must be ordered separately) |
| Protection category | IP43 (electronic components), IP22 (connection area) |
| Dimensions and weight | 180 x 249 x 100 mm / 3,5 kg |
Victron Phoenix Smart IP43 Range of Battery Chargers
Victron Phoenix Smart IP43 battery chargers are versatile and efficient chargers for use with various types of batteries. The charger has a Bluetooth Smart built-in, allowing for wireless set-up, monitoring, control, and updates.
The Victron Phoenix Smart IP43 battery charger is available in two models: the Phoenix Smart IP43 (1+1) with two outputs to charge two battery banks, and the Phoenix Smart IP43 (3) with three full current outputs to charge three battery banks. The charger has an automatic voltage compensation feature that compensates for voltage drop over the DC cabling by slightly increasing the output voltage when the DC current increases.
The Phoenix Smart IP43 battery charger also features an adaptive 6-stage charge algorithm that can be preset to suit different types of batteries. The charge algorithm can be programmed with the help of Bluetooth or the VE.Direct interface. The charger has a variable absorption time, which is automatically increased after a deep discharge to ensure that the battery will be fully charged. To prevent damage due to excessive gassing, the charger has a BatterySafe mode that automatically limits the rate of voltage increase once the gassing voltage has been reached.
The Storage Mode feature of the Phoenix Smart Charger reduces the float voltage to 2.2V/cell when the battery is not in use to minimize gassing and corrosion of the positive plates. Once a week, the voltage is raised back to the absorption level to 'equalize' the battery, preventing stratification of the electrolyte and sulphation, a major cause of early battery failure.
The Phoenix Smart Charger is also capable of charging Li-ion (LiFePO₄) batteries, and its charger on-off control can be implemented by connecting a relay or open collector optocoupler output from a Li-ion BMS to the remote on/off port. Alternatively, full control of voltage and current can be achieved with Bluetooth.
The charger also has a programmable relay that can be programmed using the VE.Direct interface or a Bluetooth-enabled device to trip on an alarm or other events. It also has a VE.Direct interface for a wired data connection to a GX device such as the Cerbo GX, PC, or other devices. The interface also enables instant readout functionality via VictronConnect remotely from VRM.
Finally, the Victron Phoenix Smart IP43 Charger is designed to be weather-resistant, with an IP43 rating indicating protection against water spray from any direction. This makes it well-suited for use in marine and RV applications, as well as in industrial and off-grid power systems.
In summary, the Victron Phoenix Smart IP43 battery charger is a versatile and reliable battery charger that offers a range of features designed to optimize battery charging and ensure safe and effective operation. Its adaptability, temperature compensation, battery profiles, Bluetooth connectivity, and weather-resistant design make it an excellent choice for a variety of applications.
Victron Accesories for the Phoenix Smart IP43 12/50 (1+1) (not inlcuded in the product)
- Victron Mains Cord CEE 7/7 for Smart IP43 Charger 2m (Ref. ADA010100100)
- Victron Mains Cord UK for Smart IP43 Charger 2m (Ref.ADA010100200)
- Victron Mains Cord AU/NZ for Smart IP43 2m (Ref.ADA010100300)
- Victron Mains Cord NEMA 6-15P for Smart IP43 2m (Ref.ADA010100500)
About Victron Energy
Founded in 1973 in the Netherlands by Reinout Vader, Victron Energy began by manufacturing and supplying inverter/chargers to the marine, land, industrial and automotive sectors. Since then it has grown to become the world leading mannufacturer in the sector of off-grid electrical power generation, both for recreational and commercial applications.
Victron Energy stands out for the quality, reliability and technical innovations of its products for battery storage and battery charging systems, as well as for its ability to provide complete customized network solutions for self-supporting electrical power generation systems.
Victron Energy has a long history, unrivaled experience and reputation in thes elf-supporting electrical power generation industry. Victron Energy products have been designed to meet the needs of any installation, regardless of the degree of difficulty that it presents.
The Victron Energy product range includes, among others:
- Inverters
- Gel batteries and AGM batteries
- Battery monitors
- Battery charger
- Solar charge controllers
- Solar panels
- Battery chargers
- Sinewave inverters
- Inverters/Chargers
- DC-DC Converters
- Transfer Switches
Victron Energy has a worldwide network of distributors and dealers that enables it to offer a fast and competent customer service and technical support network, accessible from virtually every corner of the world.
Product Warranty
Standard warranty of 5 years, extendable to 10 years with an additional 10% of the initial investment. Contact us for more information.
PSC125051085
Data sheet
- Volt (V)
- 12
- Current (A)
- 50
- Large (mm)
- 180
- Width (mm)
- 249
- Height (mm)
- 100
- Weight (kg)
- 3.5
- Bluetooth
- Yes
You might also like
Measurements: 180 x 249 x 100 mm